500|彩票一分快三平台

                                • Login
                                • Register
                                • 800-HPALLOY
                                • 1985 E 500 N Windfall, IN 46076
                                  444 Wilson St Tipton, IN 46072
                                  Post Office Box 40 Tipton, IN 46072
                                  tel:8004725569

                                NITRONIC® 60 (Alloy 218) (UNS S21800)

                                Request a quote

                                NITRONIC 60 Datasheet

                                Cr 17, Mn 8, Ni 8.5, Si 4, N 0.13, C 0.10, Fe Bal.

                                High Performance Alloys stocks and produces this grade in the following forms: Bar, flat bar, square bar, wire spool. wire cuts, loose coil, sheet, plate, strip, coil, tube, pipe, fastener, disk, machined, billet, ingot. Request quote on this grade.

                                 

                                1. Download Brochure 4 MB PDF - Or view as HTML
                                2. Download Bulletin 57 KB PDF
                                3. View Nitronic Machining Brochure
                                4. Download FDA statement concerning the use of stainless steels as food contact surfaces of equipment. 154 KB PDF

                                 

                                Overview

                                Austenitic Stainless

                                Nitronic 60 is truly an all purpose metal. This fully austenitic alloy was originally designed as a temperature alloy, and subsequently has good high temperature properties for temperatures around 1800ºF. The oxidation resistance of Nitronic 60 is similar to Type 309 S.S., and far superior to Type 304S.S. This grade is best known for its wear and galling resistance.

                                The additions of Silicon and Manganese have given this alloy a matrix to inhibit wear, galling, and fretting even in the annealed condition. Higher strengths are attainable through cold working the material and is still fully austenitic after severe cold-working. This working does not enhance the anti-galling properties as is normal for carbon steels and some stainless steels. The benefit to the cold or hot work put into the material is added strength and hardness, and the wear resistance does not decrease noticeably. Chromium and Nickel additions give it comparable corrosion to 304 and 316 stainless steels, while having approximately twice the yield strength. The high mechanical strength in annealed parts permits use of reduced cross sections for weight, and cost reductions through the use of thinner stock.

                                Several data sheets are available on the wear compatibility of this alloy with dissimilar couples, as well as self-mated coupled results. Download PDF - Or view as HTML or call for your own booklet!

                                If your galling problem occurs at less than 1500ºF, then you should think about switching to this alloy. Nitronic 60 has a better cost advantage than any other alloy available. Other materials require an additional amount of heat treating to raise their hardness, where NITRONIC 60 is excellent in the annealed condition. See more information on NITRONIC 60 HS (High Strength) properties on the NITRONIC 60HS page.

                                 

                                Characteristics

                                Corrosion Properties
                                The corrosion resistance of Armco NITRONIC 60 Stainless Steel falls between that of types 304 and 316. However, experience shows that in a wear system, a galling or siezure failure occurs first, followed by dimensional loss due to wear, and finally corrosion. Galling and wear must be the first concerns of the design engineer. Although the general corrosion resistance of NITRONIC 60 is not quite as good as Type 316, it does offer better chloride pitting resistance, stress corrosion cracking resistance and crevice corrosion resistance than Type 316 in laboratory conditions. Corrosion tests are not normally performed with NITRONIC 60 High Strength.

                                Corrosion Resistance
                                Nitronic 60’s uniform corrosion resistance is better than 304 stainless in most environments. The yield strength of Nitronic 60 is nearly twice that of 304 and 316 stainless steels. Chloride pitting resistance is superior to that of type 316 stainless; Nitronic 60 provides excellent high temperature oxidation resistance and low temperature impact.
                                Applications using Nitronic 60 are valve stems, seats, and trim, fastening systems, screening, pins, bushings and roller bearings, pump shafts and rings. Other uses include wear plates, rails guides, and bridge pins.

                                Wear Resistance
                                This alloy provides a significant lower cost way to fight wear and galling compared to Nickel or Cobalt based alloys.

                                This wear data republished from Armco brochure. NITRONIC is a trademark of AK Steel.

                                 

                                Chemistry

                                Chemical Requirements

                                Ni

                                Cr

                                Mn

                                Si

                                N

                                Mo

                                C

                                Max

                                9.00

                                18.00

                                9.00

                                4.5

                                0.18

                                0.75

                                0.10

                                Min

                                8.00

                                16.00

                                7.00

                                3.5

                                0.08

                                 

                                 

                                Tensile Data

                                Ultimate Tensile

                                Yield Strength (0.2% OS)

                                Elong. in 4D

                                R/A

                                Hardness

                                Min

                                105 KSi

                                55 KSi

                                35%

                                55%

                                Max

                                Min

                                724 MPa

                                379 MPa

                                Max

                                 

                                Ultimate Tensile

                                Yield Strength (0.2% OS)

                                Elong.

                                R/A

                                Hardness

                                Min

                                95 KSi

                                50 KSi

                                35%

                                55%

                                Max

                                Min

                                655 MPa

                                345 MPa

                                Max

                                 

                                There are other high strength properties available for sizes of bar, wire, sheet and plate. Inquire with a sales associate at High Performance Alloys for more information. See bulletin, or brochure on the material (above) for a quick overview.

                                 

                                Specifications

                                Form

                                Standard

                                Bar

                                ASTM A193 ASTM A194 ASTM A276 ASTM A479 F899 AMS 5848

                                Wire

                                Sheet

                                ASTM A240 F899

                                Plate

                                ASTM A240 F899

                                Fitting

                                 

                                Forging

                                ASTM A182
                                ASTM A193 ASTM A 194 ASTM A276 ASTM A479 F899 AMS 5848

                                Weld Wire

                                A5.9 ER218

                                Werkstof No

                                 

                                 

                                Applications

                                • Automotive valves - can withstand gas temperatures of upto 1500°F for a minimum of 50,000 miles.
                                • Fastener galling - capable of frequent assembly and disassembly, allowing more use of the fastener before the threads are torn up, also helps to eliminate corroded or frozen fasteners.
                                • Pins - Used in roller prosthetics & chains to ensure a better fit of parts (closer tolerance, non-lubricated) and longer lasting.
                                • Marine shafts - better corrosion than types 304 and 316, with double the yield strength.
                                • Pin and hanger expansion joints for bridges - better corrosion, galling-resistance, low temperature toughness, & high charpy values at sub-zero temps compared to the A36 and A588 carbon steels commonly used.

                                 

                                Carburization Resistance

                                 

                                Machining

                                MACHINING DATA
                                Carbide tools are suggested
                                for rates better than 50% of Type 304.
                                Machining Type Suggested starting rates are:
                                Single Point turning : Roughing - 0.15" depth, 0.015"/rev feed -175 SFM
                                Finishing - 0.025" depth, 0.007"/rev feed - 200 SFM
                                Drilling : 1/4" Dia hole - 0.004"/rev feed - 60 SFM
                                1/2" Dia hole - 0.007"/rev feed - 60 SFM
                                3/4" Dia hole - 0.010"/rev feed - 60 SFM
                                Reaming : Feed - same as drilling - 100 SFM
                                Side and Slot Milling : Roughing - 0.25" depth - 0.007"/tooth feed - 125SFM
                                Finishing - 0.050" depth - 0.009"/tooth feed - 140SFM
                                These rates are for carbide tools,
                                Type C-2 for roughing, drilling and reaming.
                                Type C-3 for finishing.

                                 

                                Material in this bulletin has been reprinted from Armco Bulletin No S-45, other Armco sources, and HPAlloys data.

                                NITRONIC ® is a registered trademark of AK Steel.



                                <

                                                              image

                                                              car

                                                              explore

                                                              image

                                                              Second-hand housing

                                                              mailbox

                                                              Celebrity

                                                              Second-hand housing

                                                              image